How BigLeaf works: a router on site, a network in the cloud.

BigLeaf is not another box that works through rules on site. It connects a pre-configured router in front of your firewall with Bigleaf's own Cloud Access Network – and so controls the entire path of your traffic.

The architecture as a route map

Two halves, one system: the BigLeaf router on site and the gateway clusters in the cloud form the endpoints of tunnels over each of your circuits. In between lies the public internet of your providers.

Route map: how your traffic flows with BigLeafThe company network connects through the existing firewall to the BigLeaf router. The router uses three internet circuits from different providers – fibre, DSL/cable and LTE/5G or Starlink – and builds a tunnel over each to the gateway cluster in the Bigleaf Cloud Access Network. There the traffic receives a Bigleaf-issued public IP address and reaches cloud services such as Microsoft 365, VoIP and AWS or Azure. If one circuit fails, traffic uses the remaining circuits; the public IP stays the same. Your site Internet – any providers Bigleaf cloud Destinations Fibre – provider A DSL/cable – provider B LTE/5G/Starlink – provider C Company networkClients, phones, servers Your firewallstays as it is BigLeaf routeroutside the firewall – up to 4 circuits Gateway clusterCloud Access Network Tunnel per circuit – 10 measurements/s Public IP (Bigleaf)198.51.100.24 stays the same onevery switchover SaaS & Microsoft 365 VoIP & UC AWS, Azure & web Route map: how your traffic flows with BigLeafThe company network connects through the existing firewall to the BigLeaf router. The router uses three internet circuits from different providers – fibre, DSL/cable and LTE/5G or Starlink – and builds a tunnel over each to the gateway cluster in the Bigleaf Cloud Access Network. There the traffic receives a Bigleaf-issued public IP address and reaches cloud services such as Microsoft 365, VoIP and AWS or Azure. If one circuit fails, traffic uses the remaining circuits; the public IP stays the same. Your site Internet Bigleaf cloud Fibre DSL/cable LTE/5G/Starlink Company networkClients, phones, servers Your firewallstays as it is BigLeaf routeroutside the firewall – up to 4 circuits Tunnel per circuit10 measurements/s Gateway clusterCloud Access Network Public IP (Bigleaf)198.51.100.24 stays the same onevery switchover Cloud & internetMicrosoft 365, VoIP, AWS, Azure
Simplified illustration based on the manufacturer's documentationExample IP from documentation range (RFC 5737)

A packet on its way

What happens between your network and the cloud – stop by stop.

The steps describe the operating principle according to the manufacturer's documentation. Details such as tunnel protocols or internal thresholds are not published by the manufacturer; we therefore do not state them.
  1. 1 – Your network sends as usual

    Clients, phones and servers send via your firewall. To the firewall, BigLeaf is the gateway to the internet – it gets IP address, subnet mask and gateway from the Bigleaf IP block.

  2. 2 – The router classifies and distributes

    The BigLeaf router identifies traffic types in real time (Dynamic QoS) and puts each flow on the right circuit (intelligent load balancing).

  3. 3 – Tunnels over every circuit

    According to the manufacturer, all customer traffic is tunnelled to the gateway clusters before it reaches the internet. Each circuit is measured ten times per second in both directions.

  4. 4 – Exit with a Bigleaf IP

    At the gateway cluster, traffic exits to the internet with your Bigleaf-issued public IP. Replies take the reverse path – prioritised here too.

  5. 5 – On disruption: new path, same IP

    If a circuit degrades or fails, affected flows are moved to other circuits. Because the IP lives at the gateway, remote endpoints do not notice the switch.

On site: the BigLeaf router

The router ships pre-configured with your circuit details and is installed outside the firewall. It works without manual policies and without touching your security architecture.

Circuits
up to four broadband circuits
Position
in front of (outside) the existing firewall
Setup
pre-configured, plug & play
Public addresses
Bigleaf IP block (IPv4), upgradeable
Redundancy
optional High Availability or Warm Spare
Access types
fibre, DSL, cable, LTE/5G, Starlink and other satellite, fixed wireless

Details according to the manufacturer. A datasheet is available on bigleaf.net; we name the specific hardware models for your project in the quote.

Green and white Bigleaf routers being connected with network cables
Photo: Bigleaf Networks
Map of Bigleaf POPs in North America and Europe
Graphic: Bigleaf Networks – core and edge POPs in North America and Europe

In the cloud: the Bigleaf Cloud Access Network

The gateway clusters are the second half of the architecture. They terminate your tunnels, host your public IP and connect you to the internet and cloud applications.

  • 12 points of presence (POPs) in the USA and Western Europe
  • Redundancy in every part of the network: multiple core routers, servers, transit circuits
  • Peering with more than 150 cloud, content and carrier networks
  • Operated by Bigleaf – not by one of your providers

According to the manufacturer. Which POPs serve your sites is clarified during the analysis.

More about the Cloud Access Network

Configurations

From a single office to a site where nothing may fail.

Note: the manufacturer's own Wireless Connect data plans are available in the USA only. In the DACH region you connect your own mobile contract.

  • Single circuitEven with one circuit you benefit from the backbone, prioritisation and visibility – without failover.
  • Multiple circuits (multi-circuit)Up to four circuits, all used actively. No circuit just sits in reserve.
  • High AvailabilityTwo pre-configured, bridged routers run in parallel; if one fails, the other takes over immediately.
  • Warm SpareA pre-configured secondary router takes over automatically if the primary becomes unavailable.
  • Cellular & satellite as a circuitLTE/5G routers or LEO satellite (e.g. Starlink) can be integrated as a full circuit.

The route to your stable internet connection

Rollout with RIGG and your IT partner in four stops.

  1. Analysis

    Together with you we analyse the current IT set-up and clarify prerequisites: circuits, providers, firewall, applications.

  2. Pre-configuration

    The router is pre-configured with your circuit details; the IP block is provisioned.

  3. Go-live

    Installation and testing of BigLeaf on site, switching the firewall to the Bigleaf addresses.

  4. Monitoring

    Monitoring of the configuration and circuit quality in the dashboard; alerting when problems occur.

Related questions

All questions

How does BigLeaf SD-WAN work?

BigLeaf uses a split architecture: a pre-configured BigLeaf router is installed at the site in front of the existing firewall and connected to up to four internet circuits. Over each circuit it builds a tunnel to the gateway clusters in the Bigleaf Cloud Access Network. Each circuit is measured ten times per second in both directions, and every data flow is placed on the circuit that suits it. Your public IP address is issued by Bigleaf, so it does not change when a circuit fails. Technology in detail

Can BigLeaf work with my existing firewall?

Yes. The BigLeaf router is installed outside – in front of – the firewall and works with any existing network infrastructure. The firewall's WAN port is configured with the IP address, subnet mask and gateway from the Bigleaf IP block. Rule sets, VPNs and your security concept remain under your control.

How is BigLeaf installed?

The router ships pre-configured with your circuit details. On site, the circuits are plugged into the router and the firewall is pointed at the Bigleaf addresses; the manufacturer describes a plug-and-play installation done in minutes. No manual policies are required. With RIGG and your IT partner, rollout follows four steps: analysis, pre-configuration, go-live and monitoring.

Which access types does BigLeaf support – including fibre and LTE/5G?

BigLeaf is provider-neutral and, according to the manufacturer, combines any mix of fibre, cable, DSL/broadband, LTE/5G, fixed wireless and LEO satellite (e.g. Starlink). Up to four circuits can be connected per router. Note: the manufacturer's own Wireless Connect data plans are available in the USA only; in Germany, Austria and Switzerland you connect your own mobile contract as a circuit.

Is there redundancy for the router itself?

Yes. The manufacturer offers two hardware options: High Availability with two bridged routers running in parallel, where the second takes over immediately, and Warm Spare with a pre-configured secondary router that automatically takes over if the primary becomes unavailable.

Which monitoring functions are available?

The Cloud Connect dashboard shows all sites and circuits with latency, jitter, packet loss and capacity, sends alert emails when problems occur and provides troubleshooting tools. According to the manufacturer, the Q3 2026 update added uptime and optimisation widgets and richer site overviews. About the dashboard

Ready for a more reliable internet connection?

Talk to our team about your sites and circuits. We show BigLeaf in a live demo and check how it fits into your existing infrastructure.